Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, #10-32, 1/4" Length (Pack of 100)

Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, #10-32, 1/4" Length (Pack of 100) Reviews

Other Picture

Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, #10-32, 1/4" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Super Tough Nylon 6/6 is a general purpose plastic that is suitable where high impact strength is important
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Super Tough Nylon is a modified Nylon 6/6 material which performs better at low temperatures. Impact Strength, as measured by the Izod impact test method (which measures force required to break material), is 17 pounds per foot. This is significantly tougher than standard Nylon 6/6, which is rated at 3 pounds per foot. Tensile strength is estimated to be 11,600 psi (pounds per square inch) at -40 degrees Fahrenheit. Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces, it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Super Tough Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 3/8" Length (Pack of 25)
• Acetal Machine Screw, Pan Head, Phillips Drive, #4-40, 1-3/8" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 1" Length (Pack of 100)
• Nylon 6/6 Hex Nut, #4-40 (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #2-56, 1" Length (Pack of 100)

Detail Reviews

Mar 31, 2011 21:24:07

Stainless Steel 316 Machine Screw, Round Head, Slotted Drive, 1/4"-20, 2" Length (Pack of 25)

Stainless Steel 316 Machine Screw, Round Head, Slotted Drive, 1/4"-20, 2" Length (Pack of 25) Reviews

Other Picture

Stainless Steel 316 Machine Screw, Round Head, Slotted Drive, 1/4"-20, 2" Length (Pack of 25) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Stainless Steel 316 is suitable for use where Stainless Steel 304 does not provide enough corrosion resistance
• Round head style for a finished appearance
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness. These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements. The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels. Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).

Stainless Steel 316 has a higher nickel and molybdenum content than most Austenitic stainless steels which means that this material offers more corrosion resistance without giving up strength or hardness. Tensile strength is 35,000 psi (pounds per square inch).

Round head fasteners have a dome-shaped head. An older style of head, it is typically used when replacing existing round-head fasteners where an exact match is desired. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #8-32, 1-3/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, #2-56, 1-1/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #2-56, 1" Length (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, MIL-SPEC, #6-32, 7/8" Length (Pack of 10)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #3-56, 3/8" Length (Pack of 100)

Detail Reviews

Mar 30, 2011 13:59:04

Stainless Steel Machine Screw, Flat Head, Phillips Drive, #10-32, 7/16" Length (Pack of 25)

Stainless Steel Machine Screw, Flat Head, Phillips Drive, #10-32, 7/16" Length (Pack of 25) Reviews

Other Picture

Stainless Steel Machine Screw, Flat Head, Phillips Drive, #10-32, 7/16" Length (Pack of 25) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Stainless Steel is suitable where formability and cost are important considerations
• Flat head style allows fastener to sit flush to the surface
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    

Flat head fasteners are designed to fit flush to the surface when used with countersunk holes. Length is measured from the top of the head. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #2-56, 1" Length (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, 5/16"-18, 3/4" Length (Pack of 100)
• Natural Nylon 12 Semi-Rigid Tubing, 0.075" ID, 0.125" OD, 0.025" Wall, 25' Length
• Stainless Steel 18-8 Machine Screw, Flat Head, Phillips Drive, MIL-SPEC, 1/4"-20, 5/8" Length (Pack of 25)
• Weed Eater 952701594 0.065-Inch-by-200-Foot Bulk Round String Trimmer Line

Detail Reviews

Mar 29, 2011 05:52:04

6mm x 10mm Alloy Socket Cap Screws - Pack of 100

6mm x 10mm Alloy Socket Cap Screws - Pack of 100 Reviews

Other Picture

6mm x 10mm Alloy Socket Cap Screws - Pack of 100 Feature

• Diameter: 6mm
• Pitch: 1.0 Pitch
• Uses 5mm Hex Key
• Length under head: 10 mm

Heat treated black alloy steel. Hex socket head screws, driven by a hex key.

Visit Store Now !!

Detail Products

Detail Reviews

Mar 28, 2011 00:26:05

Super Tough Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #10-24, 5/16" Length (Pack of 50)

Super Tough Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #10-24, 5/16" Length (Pack of 50) Reviews

Other Picture

Super Tough Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #10-24, 5/16" Length (Pack of 50) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Super Tough Nylon 6/6 is a general purpose plastic that is suitable where high impact strength is important
• Binding head provides a large surface area for extra surface contact under the head
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Super Tough Nylon is a modified Nylon 6/6 material which performs better at low temperatures. Impact Strength, as measured by the Izod impact test method (which measures force required to break material), is 17 pounds per foot. This is significantly tougher than standard Nylon 6/6, which is rated at 3 pounds per foot. Tensile strength is estimated to be 11,600 psi (pounds per square inch) at -40 degrees Fahrenheit. Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces, it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use.

Generally used in electrical or radio work, these fasteners are slightly undercut under the head. That provides the ability to bind stranded wire tightly and prevent fraying. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 1" Length (Pack of 100)
• Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, 1/4"-20, 1/2" Length (Pack of 25)
• Nylon 6/6 Shoulder Washer, 0.140" ID, 0.186" OD, 0.031" Thick, 0.252" Shoulder Diameter, 0.062" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Hex Head, #2-56, 1/8" Length (Pack of 100)
• Polycarbonate Machine Screw, Binding Head, Slotted Drive, #8-32, 1/4" Length (Pack of 25)

Detail Reviews

Mar 26, 2011 21:00:06

Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, M3.5-0.6, 8mm Length (Pack of 100)

Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, M3.5-0.6, 8mm Length (Pack of 100) Reviews

Other Picture

Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, M3.5-0.6, 8mm Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Zinc Plated Steel fasteners are suitable where strength and corrosion resistance are primary considerations
• Flat head style allows fastener to sit flush to the surface
• Phillips drive is designed to cam out under too much torque
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Steels are designated by a 4 number SAE Steel grade.  The first two digits indicate the primary materials used to form the steel.  The last 2 digits identify the percentage of carbon for the alloy (in hundredths).  The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch).  Zinc Plating helps to prevent corrosion.

Flat head fasteners are designed to fit flush to the surface when used with countersunk holes. Length is measured from the top of the head. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter (in millimeters), followed by the thread pitch (millimeters per thread), which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M5-0.8, 10mm Length (Pack of 100)
• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, #2-56, 1-1/4" Length (Pack of 100)
• Steel Lock Nut, DIN, M3-0.5 (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #2-56, 1" Length (Pack of 100)

Detail Reviews

Mar 25, 2011 23:17:04

Black Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, 1/4"-28, 1/4" Length (Pack of 100)

Black Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, 1/4"-28, 1/4" Length (Pack of 100) Reviews

Other Picture

Black Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, 1/4"-28, 1/4" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations; black color
• Fillister head for high torque and good hold-down strength
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 1" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #0-80, 1/8" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Hex Head, #2-56, 1/8" Length (Pack of 100)
• Nylon Socket Cap Screw, Hex Socket Drive, 1/4"-20, 1/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, #2-56, 1-1/4" Length (Pack of 100)

Detail Reviews

Mar 24, 2011 16:37:08

Black Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, #10-32, 1-3/4" Length (Pack of 100)

Black Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, #10-32, 1-3/4" Length (Pack of 100) Reviews

Other Picture

Black Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, #10-32, 1-3/4" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations; black color
• Fillister head for high torque and good hold-down strength
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 1" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, 1/4"-20, 3/8" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Hex Head, #2-56, 1/8" Length (Pack of 100)
• Nylon Socket Cap Screw, Hex Socket Drive, 1/4"-20, 1/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, #2-56, 1-1/4" Length (Pack of 100)

Detail Reviews

Mar 23, 2011 12:22:05

PVC Machine Screw, Pan Head, Slotted Drive, #10-24, 1/2" Length (Pack of 10)

PVC Machine Screw, Pan Head, Slotted Drive, #10-24, 1/2" Length (Pack of 10) Reviews

Other Picture

PVC Machine Screw, Pan Head, Slotted Drive, #10-24, 1/2" Length (Pack of 10) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• PVC is suitable where insulating properties are important and/or where exposure to water is expected
• Pan head allows for higher tightening torques
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Polyvinylchloride, or PVC, exhibits little or no water absorption, absorbing 0.05% of its weight after 24 hours of exposure to water. Because it is chlorinated, PVC also possesses natural flame retardant qualities. PVC has one of the highest dielectric strengths of plastics, at 1413 volts per millimeter, making it an excellent insulator. PVC possesses average to above average strength compared to other plastics, with a tensile strength of 7450 psi (pounds per square inch) and an impact strength of 5 force pounds (Izod Impact Scale). The primary drawback of PVC is its low melting point temperature of 140 degrees Fahrenheit.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

Detail Reviews

Mar 22, 2011 11:54:06

Nylon Machine Screw, Pan Head, Phillips Drive, M2.5-0.45, 6mm Length (Pack of 100)

Nylon Machine Screw, Pan Head, Phillips Drive, M2.5-0.45, 6mm Length (Pack of 100) Reviews

Other Picture

Nylon Machine Screw, Pan Head, Phillips Drive, M2.5-0.45, 6mm Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter (in millimeters), followed by the thread pitch (millimeters per thread), which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, M3.5-0.6, 10mm Length (Pack of 100)
• Nylon Hex Nut, M3-0.5 (Pack of 100)
• Nylon Machine Screw, Cheese Head, Slotted Drive, M6-1, 75mm Length (Pack of 50)
• Nylon 6/6 Shoulder Washer, 0.345" ID, 0.470" OD, 0.045" Thick, 0.625" Shoulder Diameter, 0.105" Length (Pack of 100)
• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)

Detail Reviews

Mar 21, 2011 11:15:04

Polypropylene Machine Screw, Binding Head, Slotted Drive, 1/4"-20, 5/16" Length (Pack of 10)

Polypropylene Machine Screw, Binding Head, Slotted Drive, 1/4"-20, 5/16" Length (Pack of 10) Reviews

Other Picture

Polypropylene Machine Screw, Binding Head, Slotted Drive, 1/4"-20, 5/16" Length (Pack of 10) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Polypropylene is suitable for applications where resistance to chemicals and water (including steam) is important
• Binding head provides a large surface area for extra surface contact under the head
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Polypropylene is a thermoplastic which is autoclavable (meaning that it can be sterilized using steam), and is non-hydroscopic (it won't absorb water even after extended periods of contact). Polypropylene has excellent chemical resistance to dilute acids, concentrated acids (except oxidizing acids), alkalis, alcohols, detergents, and water. Polypropylene resists aromatic hydrocarbons, chlorinated hydrocarbons, greases, and oils at room temperature. Maximum operating temperature is 212 degrees Fahrenheit. Polypropylene has a low co-efficient of friction and a high dielectric strength (meaning it operates well as an insulator). Polypropylene has approximately half the tensile strength and impact strength of Nylon 6/6. The tensile strength of Polypropylene is 5000 psi (pounds per square inch). Impact Strength, as measured by the Izod impact test method (which measures force required to break material) is 0.5 pounds per foot.

Generally used in electrical or radio work, these fasteners are slightly undercut under the head. That provides the ability to bind stranded wire tightly and prevent fraying. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Nylon 6/6 Shoulder Washer, 0.345" ID, 0.470" OD, 0.045" Thick, 0.625" Shoulder Diameter, 0.105" Length (Pack of 100)
• Polycarbonate Machine Screw, Pan Head, Phillips Drive, #2-56, 5/16" Length (Pack of 25)
• Polypropylene Machine Screw, Pan Head, Phillips Drive, #8-32, 1/4" Length (Pack of 25)
• Polycarbonate Machine Screw, Binding Head, Slotted Drive, #6-32, 3/4" Length (Pack of 25)
• Nylon Machine Screw, Binding Head, Slotted Drive, #4-40, 1" Length (Pack of 100)

Detail Reviews

Mar 20, 2011 07:46:04

Aluminum Machine Screw, Round Head, Phillips Drive, 1/4"-20, 1-1/2" Length (Pack of 50)

Aluminum Machine Screw, Round Head, Phillips Drive, 1/4"-20, 1-1/2" Length (Pack of 50) Reviews

Other Picture

Aluminum Machine Screw, Round Head, Phillips Drive, 1/4"-20, 1-1/2" Length (Pack of 50) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Aluminum is suitable for applications where weight and corrosion resistance are primary considerations
• Round head style for a finished appearance
• Phillips drive is designed to cam out under too much torque
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Aluminum is composed of bauxite and alumina. Pure (99%) Aluminum melts at 1220 degrees Fahrenheit. It has approximately two-thirds of the thermal and electrical conductivity of copper. Aluminum has a high strength to weight ratio and is resistant to tarnishing and corrosion. Aluminum is an extremely versatile material, it may be cast or wrought, it is available in a wide range of alloys and tempers, and it accepts many types of surface finishes, including anodizing. Aluminum is easy to machine, solder and weld.

Round head fasteners have a dome-shaped head. An older style of head, it is typically used when replacing existing round-head fasteners where an exact match is desired. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, #6-32, 1/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, 1/4"-20, 3/8" Length (Pack of 100)
• Alloy Steel Socket Cap Screw, Hex Socket Drive, 3/8"-24, 5/8" Length (Pack of 100)
• Zinc Plated Steel Split Lock Washer, #10, 0.200" ID, 0.334" OD, 0.047" Thick (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #8-32, 3" Length (Pack of 100)

Detail Reviews

Mar 19, 2011 12:20:04

Nylon Machine Screw, Pan Head, Slotted Drive, M4-0.7, 35mm Length (Pack of 100)

Nylon Machine Screw, Pan Head, Slotted Drive, M4-0.7, 35mm Length (Pack of 100) Reviews

Other Picture

Nylon Machine Screw, Pan Head, Slotted Drive, M4-0.7, 35mm Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Pan head allows for higher tightening torques
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter (in millimeters), followed by the thread pitch (millimeters per thread), which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Nylon Machine Screw, Pan Head, Phillips Drive, M2.5-0.45, 6mm Length (Pack of 100)
• Nylon Machine Screw, Fillister Head, Slotted Drive, #6-32, 1" Length (Pack of 100)
• Nylon Machine Screw, Round Head, Slotted Drive, #3-48, 1/2" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, 1/4"-20, 3/8" Length (Pack of 100)
• Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, M3.5-0.6, 10mm Length (Pack of 100)

Detail Reviews

Mar 18, 2011 16:23:27