Polycarbonate Machine Screw, Pan Head, Phillips Drive, #10-32, 7/8" Length (Pack of 100)

Polycarbonate Machine Screw, Pan Head, Phillips Drive, #10-32, 7/8" Length (Pack of 100) Reviews

Other Picture

Polycarbonate Machine Screw, Pan Head, Phillips Drive, #10-32, 7/8" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Polycarbonate is suitable where high impact strength and hardness are primary considerations
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Polycarbonate is one of the toughest, most dimensionally stable thermoplastics over a wide temperature range. Impact Strength, as measured by the Izod impact test method (which measures force required to break material), is 17 pounds per foot. This is significantly tougher than standard Nylon 6/6, which is rated at 3 pounds per foot. Polycarbonate is a relatively non-hydroscopic material; it will only absorb extremely low amounts of water even after extended exposure. Polycarbonate is very resistant to greases, oils, detergents, aliphatic hydrocarbons, most mineral acids, and the higher alcohols. It is does not perform well with chlorinated hydrocarbons, and most aromatic solvents, esters, and ketones. Polycarbonate has a blue tinted transparency with 89% light transmission. Tensile strength is approximately 10,000 psi (pounds per square inch).

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Polycarbonate Machine Screw, Binding Head, Slotted Drive, #6-32, 1/2" Length (Pack of 100)
• 30% Glass Filled Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, #8-32, 1-1/4" Length (Pack of 50)
• Nylon 6/6 Shoulder Washer, 0.318" ID, 0.374" OD, 0.187" Thick, 0.502" Shoulder Diameter, 0.44" Length (Pack of 100)
• Polypropylene Machine Screw, Binding Head, Slotted Drive, #10-24, 1/2" Length (Pack of 100)
• Acetal Machine Screw, Pan Head, Phillips Drive, #10-24, 1" Length (Pack of 100)

Detail Reviews

Oct 07, 2011 15:58:37

Nylon 6/6 Machine Screw, Fillister Head, Slotted Drive, #10-32, 7/16" Length (Pack of 100)

Nylon 6/6 Machine Screw, Fillister Head, Slotted Drive, #10-32, 7/16" Length (Pack of 100) Reviews

Other Picture

Nylon 6/6 Machine Screw, Fillister Head, Slotted Drive, #10-32, 7/16" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Fillister head for high torque and good hold-down strength
• Driven by a flat-bladed driver
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 1" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Hex Head, 1/4"-20, 2" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #6-32, 1/2" Length (Pack of 25)
• Nylon 6/6 Machine Screw, Pan Head, Slotted Drive, #4-40, 3/8" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Round Head, Slotted Drive, #4-40, 1/2" Length (Pack of 100)

Detail Reviews

Oct 01, 2011 03:35:04

Stainless Steel Machine Screw, Hex Socket Drive, MIL-SPEC, #10-32, 1-1/2" Length (Pack of 25)

Stainless Steel Machine Screw, Hex Socket Drive, MIL-SPEC, #10-32, 1-1/2" Length (Pack of 25) Reviews

Other Picture

Stainless Steel Machine Screw, Hex Socket Drive, MIL-SPEC, #10-32, 1-1/2" Length (Pack of 25) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Stainless Steel is suitable where formability and cost are important considerations
• Socket cap head fasteners are very common in industrial applications
• Drive system is a hexagon-shaped hole
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    

With a high cylindrical head, socket cap head fasteners have a recessed driving area and offer high hold power at high torque levels. Hex socket drive systems are driven by hex wrenches or power tools with hexagonal bits.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #4-40, 1-1/8" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #1-72, 5/16" Length (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, MIL-SPEC, #10-24, 2-1/2" Length (Pack of 25)
• Black Oxide Heat Treated Alloy Steel Socket Head Cap Screw, Hex Socket Drive, 3/8"-24, 3/4" Length (Pack of 100)
• Stainless Steel Socket Cap Screw, Hex Socket Drive, #8-32, 7/8" Length (Pack of 5)

Detail Reviews

Sep 29, 2011 19:30:08

Polypropylene Machine Screw, Binding Head, Slotted Drive, #10-32, 5/8" Length (Pack of 25)

Polypropylene Machine Screw, Binding Head, Slotted Drive, #10-32, 5/8" Length (Pack of 25) Reviews

Other Picture

Polypropylene Machine Screw, Binding Head, Slotted Drive, #10-32, 5/8" Length (Pack of 25) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Polypropylene is suitable for applications where resistance to chemicals and water (including steam) is important
• Binding head provides a large surface area for extra surface contact under the head
• Driven by a flat-bladed driver
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Polypropylene is a thermoplastic which is autoclavable (meaning that it can be sterilized using steam), and is non-hydroscopic (it won't absorb water even after extended periods of contact). Polypropylene has excellent chemical resistance to dilute acids, concentrated acids (except oxidizing acids), alkalis, alcohols, detergents, and water. Polypropylene resists aromatic hydrocarbons, chlorinated hydrocarbons, greases, and oils at room temperature. Maximum operating temperature is 212 degrees Fahrenheit. Polypropylene has a low co-efficient of friction and a high dielectric strength (meaning it operates well as an insulator). Polypropylene has approximately half the tensile strength and impact strength of Nylon 6/6. The tensile strength of Polypropylene is 5000 psi (pounds per square inch). Impact Strength, as measured by the Izod impact test method (which measures force required to break material) is 0.5 pounds per foot.

Generally used in electrical or radio work, these fasteners are slightly undercut under the head. That provides the ability to bind stranded wire tightly and prevent fraying. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #10-32, 2" Length (Pack of 100)
• Polypropylene Machine Screw, Pan Head, Phillips Drive, #4-40, 1-1/2" Length (Pack of 25)
• Polycarbonate Machine Screw, Pan Head, Phillips Drive, #8-32, 1-1/2" Length (Pack of 25)
• Nylon 6/6 Shoulder Washer, 0.140" ID, 0.187" OD, 0.035" Thick, 0.312" Shoulder Diameter, 0.062" Length (Pack of 100)
• Polycarbonate Machine Screw, Binding Head, Slotted Drive, 1/4"-20, 3/8" Length (Pack of 100)

Detail Reviews

Sep 22, 2011 23:51:05

Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, #10-32, 3" Length (Pack of 100)

Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, #10-32, 3" Length (Pack of 100) Reviews

Other Picture

Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, #10-32, 3" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Zinc Plated Steel fasteners are suitable where strength and corrosion resistance are primary considerations
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Steels are designated by a 4 number SAE Steel grade.  The first two digits indicate the primary materials used to form the steel.  The last 2 digits identify the percentage of carbon for the alloy (in hundredths).  The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch).  Zinc Plating helps to prevent corrosion.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Zinc Plated Steel Hex Nut with Washer, 1/4"-20 (Pack of 100)
• Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, #6-32, 1/4" Length (Pack of 100)
• Zinc Plated Steel Hex Nut, 5/16"-18 (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #4-40, 3/8" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, #2-56, 1-1/4" Length (Pack of 100)

Detail Reviews

Aug 28, 2011 01:05:04

Polypropylene Machine Screw, Pan Head, Phillips Drive, #10-32, 5/16" Length (Pack of 25)

Polypropylene Machine Screw, Pan Head, Phillips Drive, #10-32, 5/16" Length (Pack of 25) Reviews

Other Picture

Polypropylene Machine Screw, Pan Head, Phillips Drive, #10-32, 5/16" Length (Pack of 25) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Polypropylene is suitable for applications where resistance to chemicals and water (including steam) is important
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Polypropylene is a thermoplastic which is autoclavable (meaning that it can be sterilized using steam), and is non-hydroscopic (it won't absorb water even after extended periods of contact). Polypropylene has excellent chemical resistance to dilute acids, concentrated acids (except oxidizing acids), alkalis, alcohols, detergents, and water. Polypropylene resists aromatic hydrocarbons, chlorinated hydrocarbons, greases, and oils at room temperature. Maximum operating temperature is 212 degrees Fahrenheit. Polypropylene has a low co-efficient of friction and a high dielectric strength (meaning it operates well as an insulator). Polypropylene has approximately half the tensile strength and impact strength of Nylon 6/6. The tensile strength of Polypropylene is 5000 psi (pounds per square inch). Impact Strength, as measured by the Izod impact test method (which measures force required to break material) is 0.5 pounds per foot.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Acetal Machine Screw, Pan Head, Phillips Drive, #10-24, 1" Length (Pack of 100)
• Polypropylene Machine Screw, Binding Head, Slotted Drive, #10-24, 1/2" Length (Pack of 25)
• Nylon 6/6 Shoulder Washer, 0.230" ID, 0.299" OD, 0.078" Thick, 0.395" Shoulder Diameter, 0.187" Length (Pack of 100)
• Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, #8-32, 3/4" Length (Pack of 100)
• Polycarbonate Machine Screw, Pan Head, Phillips Drive, #6-32, 3/16" Length (Pack of 100)

Detail Reviews

Aug 15, 2011 05:09:09

Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/16" Length (Pack of 100)

Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/16" Length (Pack of 100) Reviews

Other Picture

Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/16" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Brass is suitable where corrosion resistance is a primary consideration
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Brass is rust proof, corrosion resistant and polishes to a rich, golden color. Brass is easily soldered and brazed and accepts plating readily. The typical composition is 70% Copper and 30% Zinc. Strength increases with a higher percentage of Zinc.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Brass Machine Screw, Round Head, Slotted Drive, #8-32, 3/16" Length (Pack of 100)
• Brass Hex Nut, #4-40 (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, #8-32, 1/2" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, 1/4"-20, 1-3/8" Length (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #10-32, 1-3/4" Length (Pack of 100)

Detail Reviews

Jul 26, 2011 03:17:04

Ceramic Machine Screw, Flat Head, Slotted Drive, #10-32, 3/8" Length (Pack of 1)

Ceramic Machine Screw, Flat Head, Slotted Drive, #10-32, 3/8" Length (Pack of 1) Reviews

Other Picture

Ceramic Machine Screw, Flat Head, Slotted Drive, #10-32, 3/8" Length (Pack of 1) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Ceramic is suitable where primary considerations are high temperature and corrosion resistance
• Flat head style allows fastener to sit flush to the surface
• Driven by a flat-bladed driver
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Ceramic is produced from low pressure injection molded ceramics, utilizing 99.8% fully dense aluminum oxide (Alumina A998). In addition to the outstanding electrical insulation properties of alumina, this material offers unusual resistance to high temperature, corrosion, and abrasion.

Flat head fasteners are designed to fit flush to the surface when used with countersunk holes. Length is measured from the top of the head. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

Detail Reviews

Jun 11, 2011 23:18:04

PTFE Machine Screw, Flat Head, Slotted Drive, #10-32, 1/2" Length (Pack of 1)

PTFE Machine Screw, Flat Head, Slotted Drive, #10-32, 1/2" Length (Pack of 1) Reviews

Other Picture

PTFE Machine Screw, Flat Head, Slotted Drive, #10-32, 1/2" Length (Pack of 1) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• PTFE is suitable for high temperature environments and for applications that have the potential for surface wear and exposure to water and chemicals
• Flat head style allows fastener to sit flush to the surface
• Driven by a flat-bladed driver
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

PTFE (polytetrafluoroethylene) has similar properties to Teflon, including an extremely low coefficient of friction (it doesn't stick to other materials and it resists surface wear). PTFE also exhibits a useful service life from below -100 degrees Fahrenheit, to temperatures of over 500 degrees Fahrenheit. Its resistance to solvents is also excellent throughout a wide range of temperatures. PTFE has a high dielectric strength (600 volts/millimeter) which makes it a good insulator. PTFE is also very non-hydroscopic, or water resistant, absorbing less than 0.01% of its weight if exposed to water for a 24 hour period. PTFE has below average tensile strength, at 3000 psi (pounds per square inch).

Flat head fasteners are designed to fit flush to the surface when used with countersunk holes. Length is measured from the top of the head. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• PTFE Machine Screw, Pan Head, Slotted Drive, #4-40, 1/2" Length (Pack of 5)
• PTFE Hex Nut, 1/4"-20 (Pack of 10)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, #2-56, 1-1/4" Length (Pack of 100)
• PTFE Sheet, White, 0.06" Thick, 6" Width, 6" Length
• Translucent Amber Miniature Polyimide Tubing, 34 AWG, 0.0063" ID, 0.0108" OD, 0.00225" Wall, 30" Length (Pack of 10)

Detail Reviews

Jun 10, 2011 17:41:32

Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #10-32, 7/8" Length (Pack of 100)

Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #10-32, 7/8" Length (Pack of 100) Reviews

Other Picture

Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #10-32, 7/8" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Stainless Steel is suitable where formability and cost are important considerations
• Fillister head for high torque and good hold-down strength
• Driven by a flat-bladed driver
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    

Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #6-32, 2" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #6-32, 1-3/4" Length (Pack of 25)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, #8-32, 1/2" Length (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, MIL-SPEC, #2-56, 5/8" Length (Pack of 100)
• Brass Machine Screw, Round Head, Slotted Drive, #00-90, 1/2" Length (Pack of 100)

Detail Reviews

Apr 26, 2011 03:31:03

Stainless Steel Machine Screw, Pan Head, Phillips Drive, #10-32, 1-1/8" Length (Pack of 100)

Stainless Steel Machine Screw, Pan Head, Phillips Drive, #10-32, 1-1/8" Length (Pack of 100) Reviews

Other Picture

Stainless Steel Machine Screw, Pan Head, Phillips Drive, #10-32, 1-1/8" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Stainless Steel is suitable where formability and cost are important considerations
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Stainless Steel Machine Screw, Flat Head, Phillips Drive, #2-56, 1-1/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, MIL-SPEC, #10-24, 1-3/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #8-32, 1-3/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #0-80, 1/8" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #2-56, 1" Length (Pack of 100)

Detail Reviews

Apr 16, 2011 21:43:04

Polypropylene Machine Screw, Flat Head, Slotted Drive, #10-32, 1" Length (Pack of 100)

Polypropylene Machine Screw, Flat Head, Slotted Drive, #10-32, 1" Length (Pack of 100) Reviews

Other Picture

Polypropylene Machine Screw, Flat Head, Slotted Drive, #10-32, 1" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Polypropylene is suitable for applications where resistance to chemicals and water (including steam) is important
• Flat head style allows fastener to sit flush to the surface
• Driven by a flat-bladed driver
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Polypropylene is a thermoplastic which is autoclavable (meaning that it can be sterilized using steam), and is non-hydroscopic (it won't absorb water even after extended periods of contact). Polypropylene has excellent chemical resistance to dilute acids, concentrated acids (except oxidizing acids), alkalis, alcohols, detergents, and water. Polypropylene resists aromatic hydrocarbons, chlorinated hydrocarbons, greases, and oils at room temperature. Maximum operating temperature is 212 degrees Fahrenheit. Polypropylene has a low co-efficient of friction and a high dielectric strength (meaning it operates well as an insulator). Polypropylene has approximately half the tensile strength and impact strength of Nylon 6/6. The tensile strength of Polypropylene is 5000 psi (pounds per square inch). Impact Strength, as measured by the Izod impact test method (which measures force required to break material) is 0.5 pounds per foot.

Flat head fasteners are designed to fit flush to the surface when used with countersunk holes. Length is measured from the top of the head. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Polypropylene Machine Screw, Pan Head, Phillips Drive, #4-40, 7/16" Length (Pack of 10)
• Polypropylene Machine Screw, Binding Head, Slotted Drive, #10-24, 3/8" Length (Pack of 25)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #1-72, 3/4" Length (Pack of 100)
• Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, 1/4"-20, 1/2" Length (Pack of 25)
• Polycarbonate Machine Screw, Binding Head, Slotted Drive, #8-32, 1/4" Length (Pack of 25)

Detail Reviews

Apr 03, 2011 02:18:04

Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, #10-32, 1/4" Length (Pack of 100)

Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, #10-32, 1/4" Length (Pack of 100) Reviews

Other Picture

Super Tough Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, #10-32, 1/4" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Super Tough Nylon 6/6 is a general purpose plastic that is suitable where high impact strength is important
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Super Tough Nylon is a modified Nylon 6/6 material which performs better at low temperatures. Impact Strength, as measured by the Izod impact test method (which measures force required to break material), is 17 pounds per foot. This is significantly tougher than standard Nylon 6/6, which is rated at 3 pounds per foot. Tensile strength is estimated to be 11,600 psi (pounds per square inch) at -40 degrees Fahrenheit. Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces, it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Super Tough Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 3/8" Length (Pack of 25)
• Acetal Machine Screw, Pan Head, Phillips Drive, #4-40, 1-3/8" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 1" Length (Pack of 100)
• Nylon 6/6 Hex Nut, #4-40 (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #2-56, 1" Length (Pack of 100)

Detail Reviews

Mar 31, 2011 21:24:07