Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, #10-24, 3/8" Length (Pack of 100)

Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, #10-24, 3/8" Length (Pack of 100) Reviews

Other Picture

Nylon 6/6 Machine Screw, Fillister Head, Phillips Drive, #10-24, 3/8" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Fillister head for high torque and good hold-down strength
• Phillips drive is designed to cam out under too much torque
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Nylon 6/6 Machine Screw, Round Head, Slotted Drive, #4-40, 3/32" Length (Pack of 100)
• Nylon Machine Screw, Pan Head, Phillips Drive, #10-24, 1-1/4" Length (Pack of 25)
• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 7/8" Length (Pack of 100)
• Nylon 6/6 Hex Nut, #4-40 (Pack of 100)
• Nylon 6/6 Machine Screw, Fillister Head, Slotted Drive, #4-40, 3/16" Length (Pack of 100)

Detail Reviews

Jul 31, 2011 00:32:04

Ceramic Machine Screw, Hex Head, #2-56, 3/8" Length (Pack of 1)

Ceramic Machine Screw, Hex Head, #2-56, 3/8" Length (Pack of 1) Reviews

Other Picture

Ceramic Machine Screw, Hex Head, #2-56, 3/8" Length (Pack of 1) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Ceramic is suitable where primary considerations are high temperature and corrosion resistance
• Hex head for easy driving
• Length is measured from under the head
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Ceramic is produced from low pressure injection molded ceramics, utilizing 99.8% fully dense aluminum oxide (Alumina A998). In addition to the outstanding electrical insulation properties of alumina, this material offers unusual resistance to high temperature, corrosion, and abrasion.

Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Ceramic Hex Nut, #10-32 (Pack of 1)

Detail Reviews

Jul 30, 2011 03:38:05

Nylon 6/6 Machine Screw, Oval Head, Phillips Drive, M10-1.5, 25mm Length (Pack of 100)

Nylon 6/6 Machine Screw, Oval Head, Phillips Drive, M10-1.5, 25mm Length (Pack of 100) Reviews

Other Picture

Nylon 6/6 Machine Screw, Oval Head, Phillips Drive, M10-1.5, 25mm Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Oval head style for recessed finish with a slightly rounded surface
• Phillips drive is designed to cam out under too much torque
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Similar to a flat-head style, the oval head style has a slightly convex top surface; it is typically used for appearance. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter (in millimeters), followed by the thread pitch (millimeters per thread), which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, M3-0.5, 20mm Length (Pack of 100)
• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 7/8" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Oval Head, Slotted Drive, M3-0.5, 12mm Length (Pack of 100)
• Nylon 6/6 Machine Screw, Round Head, Slotted Drive, #4-40, 3/32" Length (Pack of 100)
• Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, M4-0.7, 12mm Length (Pack of 100)

Detail Reviews

Jul 29, 2011 05:00:04

Brass Machine Screw, Flat Head, Slotted Drive, #000-120, 3/16" Length (Pack of 100)

Brass Machine Screw, Flat Head, Slotted Drive, #000-120, 3/16" Length (Pack of 100) Reviews

Other Picture

Brass Machine Screw, Flat Head, Slotted Drive, #000-120, 3/16" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Brass is suitable where corrosion resistance is a primary consideration
• Flat head style allows fastener to sit flush to the surface
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Brass is rust proof, corrosion resistant and polishes to a rich, golden color. Brass is easily soldered and brazed and accepts plating readily. The typical composition is 70% Copper and 30% Zinc. Strength increases with a higher percentage of Zinc.

Flat head fasteners are designed to fit flush to the surface when used with countersunk holes. Length is measured from the top of the head. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Brass Machine Screw, Round Head, Slotted Drive, #8-32, 3/16" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #4-40, 1-1/2" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #10-24, 2" Length (Pack of 100)
• Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/8" Length (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #10-32, 1-3/4" Length (Pack of 100)

Detail Reviews

Jul 27, 2011 19:14:05

Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/16" Length (Pack of 100)

Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/16" Length (Pack of 100) Reviews

Other Picture

Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/16" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Brass is suitable where corrosion resistance is a primary consideration
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Brass is rust proof, corrosion resistant and polishes to a rich, golden color. Brass is easily soldered and brazed and accepts plating readily. The typical composition is 70% Copper and 30% Zinc. Strength increases with a higher percentage of Zinc.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Brass Machine Screw, Round Head, Slotted Drive, #8-32, 3/16" Length (Pack of 100)
• Brass Hex Nut, #4-40 (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, #8-32, 1/2" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, 1/4"-20, 1-3/8" Length (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #10-32, 1-3/4" Length (Pack of 100)

Detail Reviews

Jul 26, 2011 03:17:04

Brass Machine Screw, Round Head, Slotted Drive, #1-72, 3/32" Length (Pack of 100)

Brass Machine Screw, Round Head, Slotted Drive, #1-72, 3/32" Length (Pack of 100) Reviews

Other Picture

Brass Machine Screw, Round Head, Slotted Drive, #1-72, 3/32" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Brass is suitable where corrosion resistance is a primary consideration
• Round head style for a finished appearance
• Driven by a flat-bladed driver
• Fine threads tap better into harder materials and thin walls, and are stronger in tension than coarse threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Brass is rust proof, corrosion resistant and polishes to a rich, golden color. Brass is easily soldered and brazed and accepts plating readily. The typical composition is 70% Copper and 30% Zinc. Strength increases with a higher percentage of Zinc.

Round head fasteners have a dome-shaped head. An older style of head, it is typically used when replacing existing round-head fasteners where an exact match is desired. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/8" Length (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #10-32, 1-3/4" Length (Pack of 100)
• Brass Hex Nut, #4-40 (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #4-40, 1-1/2" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #10-24, 2" Length (Pack of 100)

Detail Reviews

Jul 25, 2011 05:20:05

M4-.70X20 Phillips Pan Head Machine Screw (25 count)

M4-.70X20 Phillips Pan Head Machine Screw (25 count) Reviews

Other Picture

M4-.70X20 Phillips Pan Head Machine Screw

Visit Store Now !!

Detail Products

Detail Reviews

Jul 21, 2011 07:44:04

Aluminum Machine Screw, Flat Head, Slotted Drive, #10-24, 3/4" Length (Pack of 50)

Aluminum Machine Screw, Flat Head, Slotted Drive, #10-24, 3/4" Length (Pack of 50) Reviews

Other Picture

Aluminum Machine Screw, Flat Head, Slotted Drive, #10-24, 3/4" Length (Pack of 50) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Aluminum is suitable for applications where weight and corrosion resistance are primary considerations
• Flat head style allows fastener to sit flush to the surface
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Aluminum is composed of bauxite and alumina. Pure (99%) Aluminum melts at 1220 degrees Fahrenheit. It has approximately two-thirds of the thermal and electrical conductivity of copper. Aluminum has a high strength to weight ratio and is resistant to tarnishing and corrosion. Aluminum is an extremely versatile material, it may be cast or wrought, it is available in a wide range of alloys and tempers, and it accepts many types of surface finishes, including anodizing. Aluminum is easy to machine, solder and weld.

Flat head fasteners are designed to fit flush to the surface when used with countersunk holes. Length is measured from the top of the head. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #10-24, 2" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #10-24, 5/8" Length (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #8-32, 1" Length (Pack of 100)
• Brass Machine Screw, Pan Head, Phillips Drive, #10-32, 3/8" Length (Pack of 100)
• Brass Machine Screw, Round Head, Slotted Drive, #8-32, 3/16" Length (Pack of 100)

Detail Reviews

Jul 20, 2011 12:20:07

Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M5-0.8, 6mm Length (Pack of 100)

Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M5-0.8, 6mm Length (Pack of 100) Reviews

Other Picture

Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M5-0.8, 6mm Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Zinc Plated Steel fasteners are suitable where strength and corrosion resistance are primary considerations
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Steels are designated by a 4 number SAE Steel grade.  The first two digits indicate the primary materials used to form the steel.  The last 2 digits identify the percentage of carbon for the alloy (in hundredths).  The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch).  Zinc Plating helps to prevent corrosion.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter (in millimeters), followed by the thread pitch (millimeters per thread), which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)
• Steel Hex Nut, DIN, M3-0.5 (Pack of 100)
• Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, M4-0.7, 10mm Length (Pack of 100)
• 5mm Metric Flat Washer (100 count)
• Alloy Steel Socket Cap Screw, Hex Socket Drive, M10-1.5, 100mm Length (Pack of 10)

Detail Reviews

Jul 19, 2011 10:26:05

Nylon Machine Screw, Binding Head, Slotted Drive, #4-40, 1/2" Length (Pack of 10)

Nylon Machine Screw, Binding Head, Slotted Drive, #4-40, 1/2" Length (Pack of 10) Reviews

Other Picture

Nylon Machine Screw, Binding Head, Slotted Drive, #4-40, 1/2" Length (Pack of 10) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Binding head provides a large surface area for extra surface contact under the head
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Generally used in electrical or radio work, these fasteners are slightly undercut under the head. That provides the ability to bind stranded wire tightly and prevent fraying. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Nylon 6/6 Hex Nut, #4-40 (Pack of 100)
• Nylon 6/6 Shoulder Washer, 0.120" ID, 0.154" OD, 0.062" Thick, 0.291" Shoulder Diameter, 0.296" Length (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #10-32, 1-3/4" Length (Pack of 100)
• Super Tough Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #6-32, 3/8" Length (Pack of 100)
• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)

Detail Reviews

Jul 18, 2011 10:36:05

Precision Stainless Steel 303 Machine Screw, Fillister Head, Slotted Drive, ANSI B18.6.3, #00-90, 0.1875" Length (Pack of 100)

Precision Stainless Steel 303 Machine Screw, Fillister Head, Slotted Drive, ANSI B18.6.3, #00-90, 0.1875" Length (Pack of 100) Reviews

Other Picture

Precision Stainless Steel 303 Machine Screw, Fillister Head, Slotted Drive, ANSI B18.6.3, #00-90, 0.1875" Length (Pack of 100) Feature

• Screws conform to ANSI B18.6.3
• Precision, Burr free
• 303 Stainless Steel Material conforms to AMS-5640 Type 1, ASTM-A-582, MIL-S-7720, QQS763C, QQS764B
• Aerospace Quality
• Medical Quality

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness. These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements. The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels. Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).

Stainless Steel 303 contains 0.15% carbon, along with traces of sulfur and phosphorus which makes this a free machining alloy. Free machining refers to the ability to cut and finish the materials without heavy wear on the machining tools. Tensile Strength is 35000 psi (pounds per square inch).

Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Visit Store Now !!

Detail Products

• Nut Stainless Steel 000-120 x 5/64 across the flats x .040" Thick (Pack of 25)
• Translucent Amber Miniature Polyimide Tubing, 23 AWG, 0.0226" ID, 0.0286" OD, 0.0030" Wall, 30" Length
• Stainless Steel 304 Hypodermic Round Tubing, 11 Gauge, 0.1200" OD, 0.087" ID, 0.0165" Wall, 60" Length
• Precision Stainless Steel 303 Machine Screw, Binding Head, Slotted Drive, ANSI B18.6.3, #00-90, 0.0625" Length (Pack of 100)
• TRENDnet USB to Serial Converter TU-S9 (Blue)

Detail Reviews

Jul 17, 2011 09:54:39

Brass Machine Screw, Pan Head, Phillips Drive, #2-56, 1/2" Length (Pack of 100)

Brass Machine Screw, Pan Head, Phillips Drive, #2-56, 1/2" Length (Pack of 100) Reviews

Other Picture

Brass Machine Screw, Pan Head, Phillips Drive, #2-56, 1/2" Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Brass is suitable where corrosion resistance is a primary consideration
• Pan head allows for higher tightening torques
• Phillips drive is designed to cam out under too much torque
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Brass is rust proof, corrosion resistant and polishes to a rich, golden color. Brass is easily soldered and brazed and accepts plating readily. The typical composition is 70% Copper and 30% Zinc. Strength increases with a higher percentage of Zinc.

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material.

A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Brass Machine Screw, Round Head, Slotted Drive, #4-40, 7/8" Length (Pack of 100)
• Brass Hex Nut, #4-40 (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, #8-32, 1/2" Length (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Phillips Drive, #2-56, 1-1/4" Length (Pack of 100)
• Stainless Steel Machine Screw, Fillister Head, Slotted Drive, #10-32, 1-3/4" Length (Pack of 100)

Detail Reviews

Jul 16, 2011 14:43:14

Nylon 6/6 Machine Screw, Pan Head, Slotted Drive, M4-0.7, 30mm Length (Pack of 100)

Nylon 6/6 Machine Screw, Pan Head, Slotted Drive, M4-0.7, 30mm Length (Pack of 100) Reviews

Other Picture

Nylon 6/6 Machine Screw, Pan Head, Slotted Drive, M4-0.7, 30mm Length (Pack of 100) Feature

• Machine Screws are often used with nuts or driven into tapped holes
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Pan head allows for higher tightening torques
• Driven by a flat-bladed driver
• Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.

A threaded fastener's size name includes information about the major external diameter (in millimeters), followed by the thread pitch (millimeters per thread), which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Visit Store Now !!

Detail Products

• Nylon 6/6 Machine Screw, Pan Head, Phillips Drive, M3-0.5, 20mm Length (Pack of 100)
• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)
• Nylon 6/6 Hex Nut, M3-0.5 (Pack of 100)
• Nylon 6/6 Machine Screw, Oval Head, Slotted Drive, M3-0.5, 12mm Length (Pack of 100)
• Nylon 6/6 Hex Nut, #4-40 (Pack of 100)

Detail Reviews

Jul 14, 2011 21:03:04